At your doorstep by Jun 26 to Jun 29 with standard delivery
Analog multimeter has a broader operating temperature range than digital multimeters and can be used outdoors.
Analog clamp meter measures alternating current (AC) to 600 amp, RMS AC voltage to 600 volts (V), and resistance to 1,000 ohms.
Transformer clamp with 1.64" (41 mm) jaw opening measures current without interrupting or touching the circuit.
Needle lock secures the needle in place to protect it from damage during transport and holds the needle at a reading, even after the meter is disconnected.
Meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category IV installations up to 600V.
Measures AC current up to 300A.
Voltage up to 600V AC.
Works in temperatures from 5-DegreeF to 122-Degree F.
Operates on 50 and 60 Hz frequency.
Easy to use rotary scale.
Imported from USA.
The Amprobe RS-3 Pro analog clamp meter is an average-sensing,
manual-ranging multimeter for measuring current, voltage, and
resistance in electrical testing and heating, ventilation, and
air-conditioning (HVAC) applications and in environments where
very hot or very cold temperatures might interfere with the
performance of a digital meter. This analog meter displays
measurements with a needle that moves on a calibrated scale. It
has a broader operating temperature range than digital
multimeters and can be used outdoors. It has a clamp that
measures alternating current (AC) to 600 amp, and it comes with
detachable test leads that measure AC voltage to 600 volts (V)
and resistance to 1,000 ohms. The clamp has two jaws that close
around an electrical conductor up to 1.64" (41 mm) in diameter to
measure current without touching or interrupting the circuit. The
needle lock secures the needle in place to protect it from damage
during transport and to hold it at a reading, even after the
meter is disconnected. The resistance measurement also tests for
continuity and confirms that the circuit conducts electricity. A
finger guard on the body of the meter helps protect fingers from
This average-sensing, or average-responding, meter provides
accurate readings when measuring linear loads, such as standard
induction motors and incandescent lights, where the current or
voltage has a sinusoidal waveform. It is a manual-ranging meter
and requires that the operator choose the appropriate operating
range. It meets International Electrotechnical Commission (IEC)
safety standard 61010 and is certified for category IV
installations up to 600V, which covers measurements at the source
of the low-voltage supply, such as electricity meters and
overcurrent protection devices. The meter comes with a soft vinyl
carrying case. The meter does not require batteries for measuring
current or voltage.
Maximum alternating current (AC) input
Maximum AC voltage input
600 volt (V)
Maximum resistance detected
1.5V ANSI/NEDA-24A or IEC LR03 AAA battery (one, installed, for
0.5 amp/1,000V fast-blow fuse (installed)
Standards met and certifications
European Normal (EN); International Electrotechnical Commission
(IEC) and EN safety standard 61010-1; European Conformity (CE);
Underwriters Laboratories; Australia N10140
1 lb./445 g
9.5 x 4.0 x 1.6 inches/243 x 102 x 41 mm (H x W x D)
H is height, the vertical distance from the lowest to highest
point; W is width, the horizontal distance from left to right; D
is depth, the horizontal distance from front to back.
Clamp meters (also called clamp-on meters) measure electrical
current without cutting through wires or touching or interrupting
the electrical circuit. Available in handheld or benchtop models,
clamp meters diagnose problems in electrical equipment, wiring,
and power supplies. The meter's current clamp has two jaws that
fit around a conductor to take measurements. All clamp meters
test for current. Some come with test leads and inputs for
measuring voltage, capacitance, and resistance. They display
information either in analog or digital form. Factors that
influence meter choice include the electrical properties to be
measured, the anticipated range of results, and the desired level
of protection against transient voltages determine meter choice.
Safety ratings are based on the International Electrotechnical
Commission's (IEC) standards for low-voltage test equipment. IEC
61010 delineates four overvoltage installation categories. In
general, a meter with a category IV rating will provide more
protection against transient voltages than a meter with a lower
Amprobe manufactures electrical testing equipment for commercial,
industrial, and home use. The company was founded in 1948 and is
headquartered in Everett, WA.
What’s in the Box?
* RS-3 Pro analog clamp multimeter
* (1) Test lead set
* (1) 1.5V AAA battery (installed)
* (1) 0.5 amp/1,000V fast-blow fuse (installed
* Soft vinyl carrying case
Amprobe - 3467465 RS-3 PRO CAT IV 300A Analog Clamp Meter
Disclaimer: The price shown above includes all applicable taxes and fees. The information provided above is for reference purposes only. Products may go out of stock and delivery estimates may change at any time. Desertcart does not validate any claims made in the product descriptions above. For additional information, please contact the manufacturer or desertcart customer service. While desertcart makes reasonable efforts to only show products available in your country, some items may be cancelled if they are prohibited for import in India. For more details, please visit our Support Page.